Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Cost in Lakeside?
Garage door work in Lakeside typically runs $150 – $600 for a repair, while a full new door installation runs $700 – $2,200. Most of the calls we take in Lakeside are repairs rather than replacements, and a broken spring or a dead opener is usually the reason. The written estimate sets the final price on every job, and estimates are free. Call (866) 353-3562. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Typical garage door repair in Lakeside: $150 – $600.
- One broken spring: $180 – $340. A matched pair is usually replaced together, so a pair costs about twice that.
- New door installation: $700 – $2,200, depending on door size, material and whether the track and opener are being reused.
- Opener repair: $120 – $320. Opener installation: $250 – $550.
- We’re a garage door specialist. Garage doors only, no plumbing, no HVAC, just doors. Our technicians have up to 14 years of experience.
Garage Door Cost Breakdown (2026)
Here are the typical estimated ranges for each kind of job in the Lakeside area. These are estimates, not quotes. The written estimate you get after we look at the door is the price you pay.
| Job | Typical estimated range |
|---|---|
| Garage Door Repair (general) | $150 – $600 |
| Spring Repair (one spring) | $180 – $340 |
| Cable Repair | $130 – $250 |
| Opener Repair | $120 – $320 |
| Opener Installation | $250 – $550 |
| Panel Replacement | $250 – $500 |
| Track Realignment | $120 – $240 |
| Roller Replacement | $110 – $220 |
| New Door Installation | $700 – $2,200 |
A matched pair of springs is usually replaced together, so a pair costs about twice the one-spring range above. We don’t replace a single spring and leave its worn partner in place, because the second one is almost always on the same clock and goes within weeks. That’s the kind of call-back we’d rather avoid, and the kind you’d rather not pay for twice.
What pushes a job toward the top of a range? Rusted or bent track that needs replacing rather than straightening, a door that’s off its hinges after an impact, a cracked panel on a door model that’s no longer made, or an opener board that has to be sourced for a specific brand. What keeps a job at the low end? One failing part with everything else in good shape. A roller swap or a track adjustment on a door that’s otherwise sound is a short visit and lands near the bottom of its range.
If you’re weighing repair against replacement, our breakdown of garage door repair explains how we decide which way to go. And if the spring has already let go, the safety section below matters more than any price.
What Affects Garage Door Pricing in Lakeside
Five things move the number more than anything else. None of them are guesswork, and we’ll tell you which ones apply before we start.
- Which part failed, and how many. A single roller is a small job. A snapped torsion spring, a jumped cable and a door knocked off its track in the same event is three repairs in one visit. The door is a system, and when one part fails violently the others take the hit.
- Door size and weight. Lakeside has a mix of older single-car garages and newer two-car builds. A wider, heavier door needs heavier springs, more robust track and a stronger opener, and each of those steps up in price. A double door’s spring set handles roughly twice the load of a single door’s.
- Brand and part availability. We’re factory-familiar with 8 major garage door brands: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. That matters because parts aren’t interchangeable between them, and a technician who works on the brand you already own isn’t guessing at what fits. On older doors, a discontinued panel or opener board can push a job up or send it toward replacement.
- Material and insulation on a new door. A basic steel single door sits near the bottom of the installation range. A larger insulated door with windows and a decorative face sits near the top. The door itself is most of the cost on a replacement; labor is the smaller share.
- Whether the opener and track are reused. On a replacement, keeping a working opener and sound track saves real money. If the old opener is at the end of its life or the track is bent, adding opener installation at $250 – $550 and new track changes the total.
- Access and ceiling height. A low-clearance garage, an opener mounted tight to the ceiling, or a door with a beam running through its travel path all add time. Time is labor, and labor is part of every range.
One more thing specific to this area: Lakeside’s summers are humid and the winters bring freeze-and-thaw cycles. That combination works on metal. Springs corrode, rollers stiffen, hinges dry out, and wood door frames swell and shift. A door that ran quietly in April can start grinding by July. It’s not a defect in the door. It’s the climate doing what it does to moving metal parts, and it’s why a yearly look at the springs, cables and rollers is worth the short visit.
How to Save on Garage Door
You don’t need a coupon to keep a garage door bill down. You need to catch problems while they’re still small and avoid paying twice for the same fix.
- Fix the small thing before it becomes the big thing. A squealing roller or a grinding hinge is cheap to replace at $110 – $220. Left alone, a stiff roller loads the opener and the springs, and you end up paying for an opener repair on top of the roller job.
- Replace springs as a pair. It feels like more money up front, but doing one spring now and the second in a month means two visits instead of one. The pair is the cheaper path.
- Keep the door balanced. A door that’s properly balanced puts far less strain on the opener. If the door feels heavy when you lift it by hand with the opener disengaged, have it looked at before the opener fails.
- Lubricate the moving parts. Rollers, hinges and the spring coils benefit from a proper garage door lubricant a couple of times a year. Not WD-40 on the tracks; that attracts grit. Ask us what to use and we’ll tell you.
- Get the estimate before the work, not after. Our estimates are free. Call (866) 353-3562 and we’ll price the job in writing so there’s no surprise at the end.
Spring Repair and Cable Repair: The High-Risk Work
Springs and cables are the two parts of a garage door that can hurt someone. A torsion spring under load stores enough energy to break a wrist or worse, and a snapped cable whips. This is not a job to take on with a pair of vise grips and a YouTube video, and we’d rather tell you that plainly than sell you a spring and wish you luck. Our technicians handle torsion and extension spring work as trained specialists, which is why spring repair is core to what we do and never deferred or outsourced.
If a spring has snapped, don’t run the opener. The door is now being lifted by a motor built to assist, not to carry the full weight, and forcing it can burn out the opener and bend the track. Leave the door down, keep the kids and pets clear, and call. Spring failures don’t wait for a convenient time, which is one reason we keep emergency garage door service available for failures that cut off access or leave the house exposed. The local pro who comes out is licensed and insured as their state requires.
Cable repair sits at $130 – $250 for the same reason springs do: cables carry load, and one that’s frayed or off its drum is a safety issue before it’s a convenience one. If you see a cable hanging slack or a frayed strand, stop using the door.
Opener Repair and Installation Costs
Opener repair runs $120 – $320 and opener installation runs $250 – $550. Most opener failures we see come down to a worn drive gear, a failed logic board, a stripped trolley or a safety sensor that’s out of alignment. Sensors are often the cheapest fix of the bunch, so it’s worth having them checked before assuming the motor is gone.
Opener expertise here spans Wi-Fi and smart-home-integrated units from Chamberlain, LiftMaster, Genie, and Craftsman. If you’ve already got a smart opener and it’s dropped off the app or stopped responding to the remote, that’s a repair we handle. If you’re replacing an old unit, we’ll match the new opener to your door’s weight and travel, because an opener that’s undersized for the door is a short-lived opener. Our garage door opener repair page covers the diagnosis side in more detail.
Panel, Track and Roller Work
Panel replacement is $250 – $500, track realignment is $120 – $240, and roller replacement is $110 – $220. A single dented lower panel is worth replacing rather than living with, since the bottom panel takes the most impact and a bent one can throw the door off its track over time. Track that’s been hit by a car or bent by a door that jumped its rollers needs realigning before the door runs again. Rollers are the cheapest of the three and the ones most people put off longest, which is a shame, because stiff rollers are the quiet cause of a lot of opener wear.
Hail isn’t a common problem in this part of Virginia, so panel damage here usually comes from a bump with a car, a bicycle, or a door that came down on something in its path. If a panel is cracked and the door model is discontinued, we’ll tell you honestly whether a replacement panel is findable or whether you’re better off putting the money toward a new door. Our garage door installation service covers full replacements when that’s the sensible call.
New Door Installation in Lakeside
A new door runs $700 – $2,200 installed. The spread is wide because the range covers everything from a basic steel single door to a large insulated double door with windows. The door itself is the bulk of the cost; installation labor is the rest. We install across Clopay, Amarr, Wayne Dalton and Raynor, so the door you pick can be matched to the opening you have and the way you use the garage.
Installation is where a specialist pays for itself. The springs have to be matched to the door’s exact weight, the track has to be leveled to the floor, and the opener has to be set so it travels the right distance and reverses on contact. Get any of those wrong and you’re back on the phone in six months. If you’re starting from scratch and want to understand the choices before you buy, read our guide to garage door installation cost. And if you’re not sure whether your current door can be saved, our page on garage door replacement walks through the signs.
Repair or Replace? How to Decide
The rule of thumb: if a repair costs less than half the price of a new door and the door itself is structurally sound, repair it. If the door is old, has multiple failing parts, and the panels are hard to source, replacement usually wins on money over time.
A few clear signals that replacement is the better call: the door has rusted through in more than one place, panels are cracked and the model is discontinued, the door is off-square and won’t stay aligned after realignment, or you’re facing a spring job plus an opener job plus panel work all at once. When the total repair bill starts to approach the installation range, put the money into a new door instead.
On the other hand, a single broken spring on a sound door is a straightforward repair and nowhere near replacement territory. Same for a dead opener or a worn roller set. Our team can tell you which way to go in one visit, and that answer comes from looking at the door, not from a phone description. Call (866) 353-3562 for a free estimate.
What to Check Before You Call
A quick look saves time on the visit and helps us bring the right parts.
- Is the door stuck open, stuck closed, or partway up?
- Does the opener run but the door doesn’t move? That points to a broken spring or a disconnected trolley.
- Are the safety sensors at the base of the door aligned and lit?
- Is there a visible gap or fray in a cable? If so, stop and call. Don’t run the door.
- Does the door feel heavy when you lift it by hand with the opener disengaged? Heavy means the springs are tired.
- What brand is the door and the opener? Tell us and we’ll know what we’re working on before we arrive.
If the door won’t close at all and the house is open to the street, that’s the priority call. We offer emergency garage door service for exactly that situation, and we can work with your insurer if damage is part of the picture. For a broader view of what we handle, start at Richmond Garage Door Repair Pros.
Garage Door Pricing in Nearby Areas
Our pricing is consistent across the area, and the ranges you see here apply across the region. If you’re in a neighboring community, the numbers won’t change much, but the local housing stock might. Learn more about the areas around Lakeside:
- garage door repair in Glen Allen
- garage door repair in Short Pump
- garage door repair in Midlothian
- garage door repair in Henrico
- garage door repair in Mechanicsville
- garage door repair in Chesterfield
- garage door repair in Richmond
- garage door repair in Bon Air
FAQs – Garage Door Cost in Lakeside
How much does a garage door repair cost in Lakeside?
Garage door repair in Lakeside typically costs $150 – $600, depending on which part failed and how many parts are involved. A single roller or track adjustment lands near the low end, while a spring-and-cable job lands higher. Call (866) 353-3562 for an exact quote. Estimates are free.
How much does a broken spring cost to fix?
One spring runs $180 – $340, and a matched pair is usually replaced together, so a pair costs about twice that. We replace springs in pairs because the second spring is almost always on the same wear clock as the first. Call (866) 353-3562 to get your spring job priced.
Is it cheaper to repair or replace a garage door?
Repair is usually cheaper when the door is structurally sound and the fix is one or two parts. Replacement makes more sense when repairs stack up and approach the $700 – $2,200 installation range, or when panels are cracked on a discontinued model. Call (866) 353-3562 and we’ll tell you which way the math points.
How much does a new garage door cost installed in Lakeside?
New door installation typically runs $700 – $2,200 in Lakeside, with the door itself making up most of the cost. Size, material, insulation and windows move the number within that range. Call (866) 353-3562 for a free estimate on the door you have in mind.
Can you come today?
Same-day service is often possible, and emergency garage door service is available for failures that cut off access or leave the house exposed. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Call (866) 353-3562 and we’ll get you booked.
Get a Free Estimate on Your Garage Door in Lakeside
Whatever’s wrong with your door, you’ll get a straight answer and a written estimate before any work starts. Our technicians have up to 14 years of experience, we’re familiar with the brands you already own, and we handle the full range of work from a single spring to a complete installation. Your garage door is a 300-pound moving part, and it’s worth having someone who works on doors all day look at it. Call (866) 353-3562. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Lakeside market as of 2026. Richmond Garage Door Repair Pros offers free estimates – call (866) 353-3562.
Written by the team at Richmond Garage Door Repair Pros.
What Our Customers Say
"Keypad stopped working, which I assumed meant a whole new system. It was the batteries and a reprogram. He charged me the minimum service call and told me how to do it myself next time."
- Jodi Rhodes"Opener kept reversing halfway down. Turned out to be the safety sensors knocked out of alignment by a bicycle. He straightened them, wouldn't charge me for it, and just asked me to keep them in mind if I need real work later."
- Adam Kowalski"Track was bent and two of the rollers were shot. He straightened what he could, swapped the rollers for nylon ones, lubricated everything, and had it done in about an hour."
- Nathan Hayes